Magazine : Navin Chopra
Current
Engg in JWIL
Education
B.Tech/B.E. Electrical
Industry
Construction/Engineering/Cement/Metals
About Navin Chopra
Currently Working In Jindal Water Infrastructure Ltd, New Delhi as Engineer projects - Electrical & Instrumentation
Navin Chopra ’s experience
Engineer
at
Jindal Water Infrastructure Ltd
, Delhi, INDIA
July 2008 – Currently Working
Industry: Construction/Engineering/Cement/Metals
Presently working with Engineering Department of Jindal Aqua
Source Ltd. (Formerly Jindal Water Infrastructure Ltd), New Delhi
as Project Engineer – Electrical & Instrumentation for last 8
months. Company involves in the Designing, Detailed Engineering,
Erection and Commissioning of all types of Water Plants. I have
been associated with the following projects: a) 184 KM pipe
laying including pump houses in 8 X 135 MW Lignite Based Thermal
Power Plant at Barmer (Rajasthan) b) 8 MLD CETP at Sitaganj (
Uttrakhand) c) Up gradation of WTP from 0.6 to 8 MLD at Lodhika
(Gujrat) d) NextGen SEZ CETP Project, Pali,
Rajasthan e) Bhavnagar 45 MLD STP (BOOT) Project f) 25 KM pipe
laying including pump house at ANGUL, for Jindal Steel & Power
Ltd. Job Responsibilities Electrical Engineering
Includes: Preparing electrical drawings and
specifications Manage project schedules and
budgets Making engineering calculations in connection with
field and office assignments Investigate problems and
recommend solutions Ensure compliance with safety
requirements and standards procedures Prepare requests for
proposals and evaluate bids Directed, prepared, reviewed and
approved contract documents and specifications, making
modifications and recommending alternatives as
needed Perform highly specialized design, research, and
analysis on a project-by-project basis and advise on code
compliance Performed quality assurance and control To
prepare inspection and test plan as per requirement of customer &
drawing Coordinated projects with other departments, outside
agencies, contractors and consultants Exercised cost
control monitored schedules Preparation of Cable
Schedule like power & control with block
diagrams Preparation of purchase specifications (technical)
of cables and its BOQ. Inspection of 6.6KV HT Switchgear
panel, Checking of Control Wiring Connection, Bus bar
tightening. Inspection & Supervision for the project &
Preparation of Detailed Project Report for Power Distribution
System. Knowledge of switchgears &
accessories Electrical Protections involve in panels
Earthing and Electrical noise Preparation of power & control
circuits Load Management (connected load, running load, load
factor) Preparation of Single Line Drawing. Preparation
of Control Circuit for DOL & Star/Delta Starter. Motor
control circuits, Interlocking, Inching and Reversing etc. Job
Responsibilities Instrumentation Engineering
Includes: Perform Conceptual and detail engineering of I&C
systems Perform I&C equipment sizing, selection, and
specification for various types of I&C equipment, and produce
equipment-related documentation Provide input to the Drawing
Office for preparation of various I&C related engineering
drawings, such as: General Arrangements, Instrument Loops, Wiring
and Connection diagrams, Bill of Materials (BOM),
etc. Ensure accuracy, completeness and quality of technical
information and design documentation in accordance with the
Company QA programs and manuals Familiarity with PLC’s,
assorted communications network protocols including copper and
fiber media, power supplies, transducers, PID controllers,
relays and power distribution devices Proficient in
Engineering of Control systems SCADA & PLC’s, I/O list, Logics,
P&ID’s Development, Review of P&ID’s, Equipment
Specifications, Instrumentation applications, Instrument Index,
Control panels, Junction boxes, Cable tray routings drawings,
Control room layouts drawings, Loop drawings, Hook up drawings,
Cause and effect drawings and Field wiring
drawings. Selection of instruments & specifications &
Selection of Control Systems Selection of field
instrumentation, i.e. sensors, transmitters, controllers, in
industrial plants Familiarity with schematic capture, wire
list and BOM generation tools, and a broad spectrum of
electrical and electronic components and subsystems is
desirable Review of Basic engineering design
packages Preparation of detailed instrumentation & control
system specifications & specific requirements as per KNPC project
requirements Preparation of technical request for
quotations. Review of technical bid
evaluations Technical response and correspondence with
client on technical queries and other
clarifications Preparation of the Scope of
Work detailed engineering, based on the feed document
provided by the Client including detailed study of process flow
diagrams, modification of P & ID's Segregation &
finalization of various alarm and trip points Prepare
detailed Bill of Material. Preparation of QA/QC Inspection
test plans (ITP) and various checklists, calibration
forms. Advice the spare parts for: SCADA, PLC System & Field
equipments Responsible for modification of PLC program and
configuration necessary SCADA configuration and
maintenance PLC SIMATIC and Allen Bradley programming,
installation, testing, and maintenance. Developing Cause and
Effect Charts. Preparing preventive maintenance schedules
for field instrumentation, DCS, PLCs, and Local panels.
Instrumentation calibration, maintenance, and
installation. Instrumentation and control systems
engineering; develop P&ID's, control philosophy and
alarm/emergency/shutdown and safety instrumentation
systems. Proposal Document against Tender. P&ID
Drawings. Control philosophy. Instrument
Schedule. Instrument Specifications. Scheme for SCADA
Preparation of cable schedule. Instrument Hook up
drawings. Control loop schematic. Interlock
schemes. I/O list. Instrument List Along with
Parameters range etc. Specification Data Sheets for
Instruments. Designing of Drive Control panel Communication
with PLC
Source Ltd. (Formerly Jindal Water Infrastructure Ltd), New Delhi
as Project Engineer – Electrical & Instrumentation for last 8
months. Company involves in the Designing, Detailed Engineering,
Erection and Commissioning of all types of Water Plants. I have
been associated with the following projects: a) 184 KM pipe
laying including pump houses in 8 X 135 MW Lignite Based Thermal
Power Plant at Barmer (Rajasthan) b) 8 MLD CETP at Sitaganj (
Uttrakhand) c) Up gradation of WTP from 0.6 to 8 MLD at Lodhika
(Gujrat) d) NextGen SEZ CETP Project, Pali,
Rajasthan e) Bhavnagar 45 MLD STP (BOOT) Project f) 25 KM pipe
laying including pump house at ANGUL, for Jindal Steel & Power
Ltd. Job Responsibilities Electrical Engineering
Includes: Preparing electrical drawings and
specifications Manage project schedules and
budgets Making engineering calculations in connection with
field and office assignments Investigate problems and
recommend solutions Ensure compliance with safety
requirements and standards procedures Prepare requests for
proposals and evaluate bids Directed, prepared, reviewed and
approved contract documents and specifications, making
modifications and recommending alternatives as
needed Perform highly specialized design, research, and
analysis on a project-by-project basis and advise on code
compliance Performed quality assurance and control To
prepare inspection and test plan as per requirement of customer &
drawing Coordinated projects with other departments, outside
agencies, contractors and consultants Exercised cost
control monitored schedules Preparation of Cable
Schedule like power & control with block
diagrams Preparation of purchase specifications (technical)
of cables and its BOQ. Inspection of 6.6KV HT Switchgear
panel, Checking of Control Wiring Connection, Bus bar
tightening. Inspection & Supervision for the project &
Preparation of Detailed Project Report for Power Distribution
System. Knowledge of switchgears &
accessories Electrical Protections involve in panels
Earthing and Electrical noise Preparation of power & control
circuits Load Management (connected load, running load, load
factor) Preparation of Single Line Drawing. Preparation
of Control Circuit for DOL & Star/Delta Starter. Motor
control circuits, Interlocking, Inching and Reversing etc. Job
Responsibilities Instrumentation Engineering
Includes: Perform Conceptual and detail engineering of I&C
systems Perform I&C equipment sizing, selection, and
specification for various types of I&C equipment, and produce
equipment-related documentation Provide input to the Drawing
Office for preparation of various I&C related engineering
drawings, such as: General Arrangements, Instrument Loops, Wiring
and Connection diagrams, Bill of Materials (BOM),
etc. Ensure accuracy, completeness and quality of technical
information and design documentation in accordance with the
Company QA programs and manuals Familiarity with PLC’s,
assorted communications network protocols including copper and
fiber media, power supplies, transducers, PID controllers,
relays and power distribution devices Proficient in
Engineering of Control systems SCADA & PLC’s, I/O list, Logics,
P&ID’s Development, Review of P&ID’s, Equipment
Specifications, Instrumentation applications, Instrument Index,
Control panels, Junction boxes, Cable tray routings drawings,
Control room layouts drawings, Loop drawings, Hook up drawings,
Cause and effect drawings and Field wiring
drawings. Selection of instruments & specifications &
Selection of Control Systems Selection of field
instrumentation, i.e. sensors, transmitters, controllers, in
industrial plants Familiarity with schematic capture, wire
list and BOM generation tools, and a broad spectrum of
electrical and electronic components and subsystems is
desirable Review of Basic engineering design
packages Preparation of detailed instrumentation & control
system specifications & specific requirements as per KNPC project
requirements Preparation of technical request for
quotations. Review of technical bid
evaluations Technical response and correspondence with
client on technical queries and other
clarifications Preparation of the Scope of
Work detailed engineering, based on the feed document
provided by the Client including detailed study of process flow
diagrams, modification of P & ID's Segregation &
finalization of various alarm and trip points Prepare
detailed Bill of Material. Preparation of QA/QC Inspection
test plans (ITP) and various checklists, calibration
forms. Advice the spare parts for: SCADA, PLC System & Field
equipments Responsible for modification of PLC program and
configuration necessary SCADA configuration and
maintenance PLC SIMATIC and Allen Bradley programming,
installation, testing, and maintenance. Developing Cause and
Effect Charts. Preparing preventive maintenance schedules
for field instrumentation, DCS, PLCs, and Local panels.
Instrumentation calibration, maintenance, and
installation. Instrumentation and control systems
engineering; develop P&ID's, control philosophy and
alarm/emergency/shutdown and safety instrumentation
systems. Proposal Document against Tender. P&ID
Drawings. Control philosophy. Instrument
Schedule. Instrument Specifications. Scheme for SCADA
Preparation of cable schedule. Instrument Hook up
drawings. Control loop schematic. Interlock
schemes. I/O list. Instrument List Along with
Parameters range etc. Specification Data Sheets for
Instruments. Designing of Drive Control panel Communication
with PLC
Navin Chopra ’s education
B.Tech/B.E. [Electrical],
Kurukshetra University [May,2008]
, Kurukshetra, INDIA
Diploma [Industrial Automation including PLC,1],
Prolific System Technologies [July,2007] , Chandigarh, INDIA
Navin Chopra ’s additional information
Websites:
Hey there! Navin Chopra is using SiliconIndia.
Benefits of SiliconIndia
- Find prospects, new employees or jobs
- Get mentored by industry experts
- Get daily news updates
- Get found in search engines (Google, yahoo)
- Find coworkers and batchmates
